Hictop Hero D3 - IDEX, update Marlin (no replies)
Hi all I found one thread similar to this but it was last updated in April 2019, I want to update the Firmware on H3 Hero D3 because, whilst it works ok, the USB interface is flaky, it can't read sub...
View ArticleG26 bad behaviour!!! (no replies)
Hi Guys, i've just setup my Tevo Tornado with Marlin 2.0.x bugfix, UBL enabled. i did my mesh G29 P1 , then P3 until full, then saved, activated ETC. but when i do a G26 , the head move a bit then do...
View ArticleFilament runout sensor repurpose (no replies)
Hi all, Asked before, but ws not answered, really would like to know Repurpose the filament runout sensor Change the M600 script into M32, calling a sequenced shutdown program? Are there any other...
View ArticleMix SPI and UART modes? (no replies)
I'm using Marlin 2.0 on a SKR V1.3 board. Anyone know of any reason I can't mix UART and SPI modes on the same board? X,Y,Z and E0 would be SPI, E1 would be UART.
View Articlehelp me plz adding fiber sensor (no replies)
Sorry i'm not good at English. i want to adding fiber sensor in my 3d printer. sensor spec : NPN fiber sensor , 3 line : V+, GND , S i can't make custom g-code, because it's too hard. I tried several...
View ArticleMarlin 2.0 AutoBedLeveling Adjust speed (no replies)
Hi. I have a problem, and I have set my AutoBedLeveling a bit faster, but the machine crashes very hard when it drives to the next point. Is there a way that the machine drives faster to the next...
View Article#DeltaKosselMini #Marlin #BedLevellingIssue/AllenKey :X (no replies)
Hello everyone, i'm leveling bed my kossel mini. I used Marlin 1.1.9 and bugfix1.1. Type of probe i used was allen key and type of bed levelling was bilinear. When leveling bed, this probe move and...
View ArticleUpgrading to Marlin 1.1.9 (1 reply)
can any body tell me Does the latest firmware of Marlin supports the resuming of printing after accidental power shut down?
View ArticleZ lift after homing and not returning (1 reply)
Hi... I have a Flsin plus i3 which is about to go flying out a window... Couldn't get auto Level to work so I thought id go back to a micro switch, simple... no. Every time I home the Z-axis it lifts...
View ArticleBLTouch 1.1.9 bugfix-1.1.x (3 replies)
I installed example configuration for Ender 3 so i can install BLTouch to printer. Only one issue so far I've come across The line below (as of current version) 127 //#define BLTOUCH, //if...
View ArticleMarlin 2.x new jerk causing weird stuttering issues (no replies)
I so have replaced one of my old board with the mks v1.3 and have been working on setting up marlin 2.x I got everything to the point that I can print but when printing I noticed that it would break...
View ArticleRandom droput of ps_on during print (no replies)
I've selected POWER_SUPPLY 1 and enabled AUTO_POWER_CONTROL, taken 5v from RAMPS to SSR to ps_on, and it generally works fine... except partway through a print the PSU goes off for about 0.2s, which...
View ArticleRunning a G28 X and X 0 always end up 4mm apart (2 replies)
Hello, I am in the process of replacing the Crealtiy 2.1 mainboard in my CR10S with a SKR 1.3 running BTT 2209 v2.1's in UART mode. I have separated out the second Z stepper onto the E1 connector but...
View ArticleZ probe Issues Will not lock in - value (no replies)
Been playing with this, using marlin 1.1.9, attached is configuration.h file. My bltouch is actually -4.5mm on from my print head on the Z. This is a custom Core X/Y of my own design. every time i set...
View ArticleBltouch not working properly (no replies)
Hi. I have a Bltouch that I've gotten from the Creality's upgrade kit. It's the Bltouch V3.1 and triggering seems to work properly. I've been using the Bltouch for a little more than a week and it has...
View ArticleMarlin / Anet - Skew Compensation not working (4 replies)
Hello, I've spent a lot of time on this site and others trying to correct this. I printed the test print as described in the Marlin firmware (see pic), I then inputted all the measurements (after...
View ArticleChanging from Repetier to Marlin (7 replies)
Circumstances are forcing me to change from Repetier firmware to Marlin so I have been looking through the Configuration and various other files to get my system working. While I am very familiar with...
View ArticleManual Configuration of Kossel Printer (no replies)
I am using manual configuration of Marlin for my FLsun mini Kossel printer. I found the auto levelling process too inaccurate for my printer mechanics. My issue is after I get the Z0 position set for...
View ArticleDual Independent X axis and G29 Auto bed level (no replies)
Hi, I've just put together an AM8 + IDEX, and am using a servo Z probe on T0. G29 only probes a small area in the low X and high Y quadrant. I'm using bilinear levelling, and both hotend can travel...
View ArticleCan't adj z offset -skr1.3-bltouch (no replies)
I've recently installed an skr1.3 in my monoprice maker select 2.0. I know 32 bits is overkill but went with i because its cheap and the benefits of the bed leveling. Auto home works ok and the 9...
View Article